Library

Report summarizing the requirements to strenghthen new homes against property damage caused by high wind occurrences per the IBHS Fortified Homes High Wind Standard for New Homes.

Report summarizing the requirements for strenghtening and protecting the roof, openings in the house, and creating a continuous load path to strengthen walls and foundation per the IBHS Fortified Homes Hurricane Standard for New Homes.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Document describing three methods for elevating a home out of the flood zone.

Standard outlining industry procedure for sizing residential duct systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Standard covering sizing strategies for all types of cooling and heating equipment, as well as how to use comprehensive manufacturer’s performance data on sensible, latent, or heating capacity for various operating conditions.

Article describing how to detail head flashing above a window.

Document providing guideance and considerations for duct design in an energy efficient house.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Information sheet with details on pan flashing for exterior walls.

Report providing water management details for roof assemblies.

Document providing guidance to U.S. home builders who want to accept the challenge.

Guide describing measures that builders in the cold and very cold climates can take to build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Guidance document providing BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods.

Report summarizing research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Marine Climate Region on a cost-neutral basis.

Document detailing how to build radon-resistant homes.

An article illustrating common errors found in fiber cement siding installations. Many of these errors and poor flashing examples apply to siding materials beyond fiber cement siding.

Report outlining the steps developers can take to create high-performance standards on a community-wide scale.

Technical report detailing a study in which actual cooling loads are compared to modeled cooling loads.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Design and Construction Process chapter provides detailed guidance for each process phase: pre-planning, planning, construction, test-out and post-occupancy.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Lessons Learned chapter focuses on successful deep energy retrofit projects throughout the U.S.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Occupant Behavior chapter discusses how to assess homeowner behavior patterns and use these patterns to enhance overall energy savings.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Reducing costs and Increasing Cost-Effectiveness chapter provides suggestions for controlling deep retrofit costs, including both 'do's' and 'don'ts'.

Report identifying two barriers that limit the ability of builders to explore opportunities for higher levels of energy efficiency in housing: the use of duct system materials that inherently achieve airtightness and are right-sized for low-load houses, and, the ability to air seal fire separation...

Article describing a case study in which a whole-house battery and PV system was tested in a home with cooling and refrigeration during a hurricane in Florida.

Fact sheet describing weatherstripping materials, types, expected life expectancy, installation requirements, and pros and cons.

Report summarizing the requirements for strenghtening and protecting the roof, openings in the house, and creating a continuous load path to strengthen walls and foundation per the IBHS Fortified Homes Hurricane Standard for Existing Homes.

Checklist providing good and bad methods of fortifying the roof, especially in high wind situations.

Checklist providing good and bad methods of fortifying the roof, especially in hurricanes.

Checklist providing information about the specific requirements of FORTIFIED Roof™ design and construction standard for re-roofing specific for high wind resistance.

Checklist providing information about the specific requirements of FORTIFIED Roof™ design and construction standard for re-roofing specific for high wind and hail resistance.

Checklist providing information about the specific requirements of FORTIFIED Roof™ design and construction standard for re-roofing specific for hurricane resistance.

Website providing technical documents of checklists, calculators, bulletin, modular home toolkit, standard details, and corrosion resistance requirements – map set; describing the requirements of the IBHS Fortified Home program to improve the disaster resistance of new and existing homes.

Guide describing how and where to install flashings in order to weatherproof a roof.

Guide by the Northeast Energy Efficiency Partnerships on how to size heat pumps in a cold climate.

Presentation about proper installation of flexible ducts.

A article about the best practice method of installing fiber cement siding, to install flashing at the butt joints of the siding boards, rather than face caulking the butt joints afterwards.

Website blog with guidance about calculating heat-loss.

Article describing the second step of a three-step process for the installation a tubular skylight, using peel-and-stick flashing tape instead of roof cement, and integrating the roof underlayment with the flashing.

Article describing what evaporative coolers are, how they work, different types, performance, where they are appropriate, and how to install and maintain them.

Article describing how to counterflash a chimney by tucking the upper pieces of counterflashing into the chimney mortar joints and overlapping them over the various pieces of base flashing, which are nailed to the roof deck.

Report with guidance for installing windows with foam sheathing on wood-frame walls.

Article showing steps for kick out flashing at roof-wall intersection.

Article describing a technique for installing a skylight and avoiding potential water leaks with the use of a peel-and-stick (or self-adhesive) membrane under the flashing.

Article describing the flashing of roofs and what to look for, targeted at home inspectors.

Siding installation guide for Ply Gem Siding Group products.

Report providing step-by-step instructions for heating contractors and hydronic designers for selecting the proper control settings to maximize system performance and improve response time when using a thermostat setback.

Measure Guideline research report providing simple, long term, and durable solutions when using tapes and flashing membranes in conjunction with the exterior face of rigid polymeric foam sheathing to create the drainage plane of a wall system.