Library

Expert meeting describing meeting details for recommendations for applying water heaters in combination space and domestic water heating systems.

Expert meeting held to discuss simplified space conditioning systems in low load homes, including the relationship between advanced thermal enclosures, space conditioning systems and comfort.

Expert meeting held to review and discuss results and future plans for research to improve the performance of hydronic heating systems using condensing boilers and baseboard convectors.

Report on high-R wall design called extended plate and beam that uses foam sheathing insulation with wall framing.

Information sheet about what length screws should be used, and how closely to space the screws when fastening furring strips to a foam-sheathed wall.

Information sheet providing detail about hand fabrication of a one-piece straight duct from a 48" x 120" x 1" thick (1.22 m x 3.05 m x 25 mm) sheet where the total inside duct dimensions equals 112" (2.84 m) or less.

Standard providing a comprehensive approach to evaluating, selecting, specifying and installing flexible duct in HVAC systems.

Factsheet describing ways to install sheathing over existing 1x roof decking.

Checklist describing requirements for roof sheathing along the gable end truss or rafter to achive a FORTIFIED Roof, including New Roof designations and exceptions.

Checklist highlighting key concepts of wind design uplift pressures and design uplift pressure ratings for proper selection and installation of residential roof covering systems to comply with section R905.1 of the 2015 International Residential Code for a FORTIFIED Roof™–New Roof designation.

Checklist providing selection and installation guidance for residential, non-structural metal roof systems installed over wood roof decks with a roof slope 2:12 or greater to comply with section R905.1 of the 2015 IRC for a FORTIFIED Roof – New Roof Designation.

Checklist providing additional guidance and options for asphalt shingle installations at roof edges, intersections and valleys.

Website offering an online training that teaches disaster-resistant best practices for roofers.

Document that gives a step-by-step approach for designing attachments for cladding materials through foam sheathing.

Presentation about proper installation of flexible ducts.

Report providing information about energy-efficient heating, ventilation, and cooling (HVAC) equipment options to help homeowners cut their energy use, reduce their carbon footprint, and increase their homes comfort, health, and safety.

Standards criteria supporting ICC HVAC duct support standards.

Report evaluating the relative effectiveness of various control and distribution strategies to improve hydronic space heating performance in existing low-rise multifamily buildings

Research study describing the impact resistance performance of advanced framed wall systems with insulating sheathing as the primary sheathing from wind blown debris.

Report summarizing approaches to addressing duct leakage in hot humid climates.

Report showing installers how to attach ducts, pipes, and associated equipment to buildings to minimize earthquake damage.

Report describing as-found interior platform return plenums, the magnitude of their contribution to the total amount of duct leakage, and techniques and results of retrofits executed by the HVAC trade during equipment replacement.

Article showing steps for kick out flashing at roof-wall intersection.

Report presenting lab evaluation of five heat pump water heaters available in the US market today.

Report proposing mini-split heat pumps as a new retrofit option to replace resistance heating in the Pacific Northwest.

Report on the long-term performance of mini-split heat pumps.

Document presenting a cost effective method that was used by four builders in the Gainesville, FL area to construct interior ducts in over a dozen site built homes.

Report identifying the target market for solar water heaters and potential pathways and cost/performance targets that must be met for these systems to realize large energy savings.

Factsheet describing how to test the duct leakage of a manufactured home in the manufactured home factory.

Siding installation guide for Ply Gem Siding Group products.

Document pertaining to design and application guidance for combination space and tankless domestic hot water heating systems used in residential buildings, based on field evaluation, testing, and industry meetings.

Document intended for designers and installers of hydronic heating systems interested in maximizing the overall system efficiency of condensing boilers when coupled with baseboard convectors. It is applicable to new and retrofit projects.

Case study about how to properly tape insulating sheathing drainage planes.

Document with evaluation of 14 heat pump water heaters (including three recently released HPWH products) installed in existing homes in the northeast region of the United States.

Report providing guidance on how to implement a compact duct system inside a plenum truss bulkhead of a one-story, slab-on-grade home.

Report describing recommendations for optimizing flexible duct, constant-volume HVAC systems using junction boxes.

Document covering the technical aspects of buried and insulated ducts (BEDs), as well as the advantages, disadvantages, and risks of BEDs compared to alternative strategies.

Report describing the sealing and insulating of HVAC duct systems in existing homes.

Document illustrating guidelines for efficient installation of interior duct systems in new housing.

Document developed to help residential builders and retrofitters transition from tank-type water heaters to tankless water heaters.

Research study analyzing measured energy savings from a moderate retrofit by comparing post-retrofit performance with measured pre-retrofit monitored data.

Standard that prescribes a testing method to determine the efficiency of space heating and/or cooling thermal distribution systems under seasonal and design conditions. This version of the standard was published in the year 2014, and is available for preview and purchase at the reference link. The...

Discussion of building sheathing.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

Report on the use of vapor diffusion ports to reduce moisture issues with buried ductwork in unvented attics in hot-humid climates.

Report detailing a three-winter study on unvented roof assemblies in a cold climate, assessing insulation material, ridge diffusion vent presence, vapor control membranes, relative humidity, and interstitial airflow. Results indicate that utilizing air-permeable fibrous fill insulations in unvented...

Report detailing a three-winter study on unvented roof assemblies in a cold climate, assessing insulation material, ridge diffusion vent presence, vapor control membranes, relative humidity, and interstitial airflow; results indicate that utilizing air-permeable fibrous fill insulations in unvented...

Conference paper making the case that moving ducts to conditioned space saves energy, is practical for production builders (when accompanied by careful pre-planning), and creates significant andmarketable energy savings for homebuyers.

This report is designed to meet ASHRAE 62.2-2010/2013 and ANSI/ACCA’s 5 QI-2015 protocol, thereby improving the performance of HVAC equipment in new homes when compared to homes built to minimum code.

Guide providing information on controlling attic ductwork sweating.