Library

Conference paper making the case that moving ducts to conditioned space saves energy, is practical for production builders (when accompanied by careful pre-planning), and creates significant andmarketable energy savings for homebuyers.

This report is designed to meet ASHRAE 62.2-2010/2013 and ANSI/ACCA’s 5 QI-2015 protocol, thereby improving the performance of HVAC equipment in new homes when compared to homes built to minimum code.

Document describing recommended modeling rules, potential compliance credits, and eligibility criteria for residential night ventilation cooling systems for California’s Title 24 energy efficiency standards.

Guide providing information on controlling attic ductwork sweating.

Fact sheet describing a novel, simplified air delivery system using a plug-and-play model that features 3-inch diameter flexible ducts, efficient fittings, and a simplified installation process that resulted in successful market engagement through commercialization.

Document about development of recommendations to help residential HVAC designers select optimal supply inlet size and system operating conditions to maintain good thermal comfort in low heating and cooling load homes.

Research study using modeling to determine optimal combination(s) of components/pumps, high efficiency heat sources, plumbing configurations and controls that result in the highest overall efficiency for a hydronic system.

Report describing a field study to measure pollutant concentrations in 324 homes in California.

Website with information about radon-resistant construction techniques and other radon resources for builders, contractors and homebuyers.

DOE case study findings on raised ceiling interior duct systems.

Report including an overview of the buried duct research and information the retrofit methodology used to install and test the three existing duct systems, including short- and long-term data collection.

Document presenting results from testing prototype HVAC duct system designs that would locate the entire length of duct work within the air and thermal barriers of the building envelope. These include one that incorporated a high-side supply register, one that utilized a single soffit located within...

Presentation providing information about correctly installing ductwork in new and existing homes.

Report proposes high performance duct measures for inclusion in California Title 24 building energy efficiency standards for 2016.

IECC code note explaining new fan efficacy requirements, along with how to determine which fans are affected by the new fan requirements.

Research study about a high performance retrofit of an existing brick building (a former convent) into condominiums, all affordable housing.

Report describing procedures for increasing sensible efficiencies through increased flow rates across the air handling unit and increased indoor coil sizes.

Report about cost effective energy-efficient upgrades that can be implemented in the hot, dry Southwest climate.

This research paper outlines residential HVAC advanced controls and sensors. It includes a technology review, applications, maintenance and commissioning, occupant behavior and a summary of the state-of-the-art technologies for advanced controls for residential HVAC.

Document reviewing current and potential ventilation technologies for residential buildings with particular emphasis on North American climates and construction.

Article describing how insulating and air sealing unfinished attic spaces can lead to reduced energy bills in some homes.

Report describing development of a package of energy efficiency measures to achieve 60% energy savings in a test house.

Website with consumer information about duct cleaning.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

Report addressing barriers to information, contractor resources and cost savings associated with steam balancing multifamily buildings.

Information sheet about buried ducts.

Report about the impact on the loads when common safety factors are applied to the load calculation process using two houses that meet the 2009 IECC prescriptive path modeled as the accurate baseline.

Document covering the pros and cons of compact air distribution systems and the decision criteria that must be considered early in the whole-house design process.

Report about proper water heater selection developed to provide step-by-step procedures for evaluating preferred cost-effective options for energy efficient water heater alternatives based on local utility rates, climate, and anticipated loads.

Report describing findings from research related to heating, ventilation, and air conditioning (HVAC) companies that have made the decision to transition to whole house performance contracting (WHPC).

Question and Answer article in Energy Design Update describing the cost and savings benefits of electronically commutated motors (ECMs) for HVAC equipment.

Article describing a field study that test ventilation performance in nine homes and found current ventilation was inadequate to remove PM2.5 and CO2 levels; however, a directly exhausting range hood can reduce peak PM2.5 concentrations by 75% or more.

Standard providing industry-backed information for assessing new and existing HVAC systems, evaluating and verifying the cleanliness of HVAC system components, preventing job related hazards and guiding the cleaning and restoration of HVAC systems to a specific level of cleanliness.

Information sheet describing transfer ducts and grilles for HVAC.

Research study comparing TRNSYS Type 604 pipe model against laboratory pipe heat loss test data and detailed field monitoring data.

Preliminary results of two monitored lab homes constructed to represent the thermal characteristics of typical existing Florida homes are presented.

Information sheet about proper ventilation and air sealing.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2010, and is available for...

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2013, and is available for...

ENERGY STAR overview on certified ventilation fans.

This report describes how twenty homes were tested and monitored in the Zone 2 climate of Houston, Texas, U.S.A., to evaluate the humidity control performance and operating cost of six different integrated dehumidification and ventilation systems that could be applied by production homebuilders.

Guide providing information on controlling attic ductwork sweating.

Brochure about how to install and use a whole-house fan.

Report describing the design and construction of a highly energy efficient community of ten duplexes in Greenfield, Massachusetts.

Report and case study describing a retrofit project for single family homes in the Pacific Northwest.