Library

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2009 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Florida building code including all the amendments and additions by Florida for the wind-borne debris regions and the high-velocity hurricane zone.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Webinar answering code-related questions on duct leakage tests, moisture levels in attics and crawlspaces, combustion equipment in conditioned attics, ventilation in multifamily buildings, and continuous insulation in residential construction.

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height. Walls with...

Presentation describing the history of ECM motors, an overview of ECM motor technology, and a lesson on the installation of ECM motors.

A standard providing minimum energy efficiency requirements for buildings that are not low-rise residential buildings.

Standard providing a comprehensive approach to evaluating, selecting, specifying and installing flexible duct in HVAC systems.

Fact sheet describing foundation design criteria, foundation types suitable for coastal environments, and addressing foundations for high-elevation coastal areas (e.g., bluff areas); also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Fact sheet describing the function of housewrap, its attributes, and common problems associated with its use, including housewrap vs. building paper and housewrap installation; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Fact sheet describing effects of planning, siting, and design decisions on coastal home costs, including initial, operating, and long-term costs; risk determination; and the effect on costs of meeting and exceeding code and NFIP design and construction requirements; also published in FEMA P-499...

Report describing the interactions, both positive and negative, between common green building practices and the robustness of residential buildings to withstand natural hazards.

Standard providing a procedure for determining fenestration attachment product U-factors.

Standard for determining fenestration attachment product SHGC and visible transmittance.

Standards for paints and coatings.

An example of a form a building codes department created to ensure builders are fully aware and have taken steps to provide drainage so that water doesn’t accumulate behind siding. This example is from the city of Newberg, Oregon.

Fact sheet describing an alternative to piles in V Zones and A Zones in coastal areas where soil properties preclude pile installation, but the need for an “open foundation system” still exists and recommendations for good masonry practices in coastal environments; also published in FEMA P-499 “Home...

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes. The current version of this standard was published in the year 2017, and is available in both digital and print...

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Website providing a link for purchasing NFPA 1141, Standard for Fire Protection Infrastructure for Land Development in Wildland, Rural, and Suburban Areas.

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

Detailed requirements for testing, exposure modeling, and allowable limits for modeled indoor air concentrations.

The 2017 publication update to the SEAOC Wind Committee and SEAOC Solar Photovoltaic Systems Sub-Committee's 2012 report.

Fact sheet describing best practices for flashing doors and windows to minimize air and water intrusion.

The Technician's Guide equips practitioners with the knowledge to properly implement all of the measurement procedures required in the HVAC QI Specification.

Document with information on preventing termites when using ICFs.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2010, and is available for...

Standard that provides expanded and updated requirements for producing, marketing, and specifying plywood for construction and industrial uses.

Report providing guidance on how to improve the wind resistance of existing residential buildings in Mississippi and across the Gulf Coast.