Library

Guidelines to assist builders in designing and constructing homes equipped with a set of features that make the installation of solar energy systems after the completion of the home’s construction easier and less expensive.

Report identifying the important aspects of building design and construction to enable installation of solar photovoltaic and heating systems at some time after the building is constructed.

Website describing how solar water heaters -- also called solar domestic hot water systems -- can be a cost-effective way to generate hot water for your home.

The RERH specifications and checklists take a builder and a project design team through the steps of assessing a home’s solar resource potential and defining the minimum structural and system components needed to support a solar energy system.

Specifications to assist builders in designing and constructing homes equipped with a set of features that make the installation of solar energy systems after the completion of the home’s construction easier and less expensive.

Research study presenting a unique opportunity to both identify and evaluate deep retrofit measures that are practical and potentially cost effective for the retrofit market, as well as review the cost effectiveness of the Passive House design approach for achieving energy savings in deep retrofits.

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Proposed HVAC filter labeling standard and underlying analysis by the California Energy Commission.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2016, and is available for...

A standard providing minimum energy efficiency requirements for buildings that are not low-rise residential buildings.

Website providing a link for purchasing NFPA 1141, Standard for Fire Protection Infrastructure for Land Development in Wildland, Rural, and Suburban Areas.

Website providing a link for purchasing NFPA 703, Standard for Fire Retardant—Treated Wood and Fire–Retardant Coatings for Building Materials.

Standard establishing requirements for the performance and installation of gasketing systems including mortised to doors, frames or both which was published in the year 2021 and a can be purchased to be viewed in full from the ANSI webstore in the link.

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

Website providing a link for purchasing NFPA 1144, Standard for Reducing Structure Ignition Hazards from Wildland Fire.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Webpage containing the latest version of ANSI/RESNET/ICC 380, Standard for testing Airtightness of Building Enclosures, Airtightness of Heating and Cooling Air Distribution Systems, and Airflow of Mechanical Ventilation Systems. This standard provides a consistent, uniform methodology for evaluating...

Link to find the latest version of ANSI/RESNET/ICC 301, a standard providing a methodology for calculating Energy Rating Index for code compliance.

Website containing links to key wildfire codes and standards.

Standard covering the installation of fenestration products in new and existing construction, which was published in the year 2019, and is available for preview and purchase at the referenced link.

Standard covering the installation of fenestration products in new and existing construction which was published in the year 2007, and is available for preview and purchase at the referenced link.

Standard describing methods for installing radon mitigation systems in existing residential buildings three stories or less in height which was published in the year 2021 and is available for preview and purchase at the reference link.

Detailed requirements for testing, exposure modeling, and allowable limits for modeled indoor air concentrations.

Standard specification covering the minimum performance and acceptance criteria for an air barrier (AB) material or system for framed walls of low-rise buildings with the service life of the building wall in mind.

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2022, and is available for preview and purchase at the reference link. There are also other versions of...

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2023, and is available for preview and purchase at the reference link. There are also other versions of...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2011 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2021, 2015, 2006, and...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2021 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2015, 2011, 2006, and...

Standard specification covering the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements...

ASTM standard for wood-composite decking and guardrail materials under a variety of tests, including fire performance and UV resistance. Available for preview and purchase at the reference link.

A specification covering the application of Insulating Concrete Forms (ICFs) that act as permanent formwork for cast-in-place reinforced concrete beams & walls which was published in the year 2022 and is available for preview and purchase at the reference link.

Test method designed to calculate an assigned air permeance of flexible sheet or rigid panel-type materials at a reference air pressure differential of 75 Pa which was published in the year 2021 and is available for preview and purchase at the reference link.

Standard describing a test method measuring air-leakage rates through a building envelope under controlled pressurization and de-pressurization which was published in the year 2019 and is available for preview and purchase at the reference link.

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

Standard describing a test method for mold growth resistance on interior coatings such as paint in an environmental chamber; the 2021 version of this standard is available for preview and purchase at the referenced link.

Test method providing a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. This version of the standard was published in the year 2021 and is...

Test method designed to obtain reliable values for the WVTR of plastic film and sheeting which was published in the year 2020 and is available for preview and purchase at the reference link.

Standard describing two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone which was published in the year 2022 and is available for preview and purchase at the reference link.

The Standard Work Specifications (SWS) are a tool for industry guidance to ensure effective, durable, and safe work is performed during home upgrades.

Report addressing barriers to information, contractor resources and cost savings associated with steam balancing multifamily buildings.

Report about results of 10 test buildings in Chicago, studied to identify best practices for methodology, typical costs, and energy savings associated with steam system balancing.

Website providing information on all types of pest management for multi-family housing.

Document describing correct construction of swales, designed to trap particulate pollutants (suspended solids and trace metals), promote infiltration, and reduce the flow velocity of storm water runoff.

ENERGY STAR webpage describing the benefits of storm windows and a link to a product list.

Webpage providing an ENERGY STAR climate zone map and criteria for ENERGY STAR storm windows per climate zone.

Report providing information based on research and case studies, to remodelers and consumers about opportunities to increase home energy performance.

Report recommending strategies and approaches that the Federal government and other stakeholders may take to encourage and aid States and local communities in the adoption of the most current building codes.

Report about the impact on the loads when common safety factors are applied to the load calculation process using two houses that meet the 2009 IECC prescriptive path modeled as the accurate baseline.

Report following the evolution of the construction quality process from its development for new homes to its application construction of a HPH with enhanced specifications, and its application in a crawlspace renovation.

Document explaining the benefits of evaluating and identifying energy efficiency retrofit measures that could be made during renovation and maintenance of multifamily buildings.