Library

Fact sheet describing improvements in the earthquake resistance of residential and commercial new construction through the adoption into the International Residential Code of seismic provisions including those developed by the National Earthquake Hazards Reduction Program (NEHRP).

Website providing links to building codes, seismic codes, code enforcement, safe buildings, and seismic retrofitting.

Document describing precast concrete earthquake design considerations including connections, detailing, and forces, among others.

Website providing an introduction to the concepts and principles of seismic design.

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes.

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes. The current version of this standard was published in the year 2017, and is available in both digital and print...

Newsletter containing five articles focused on seismic retrofitting.

How hard can it be to insulate a flat sheet of concrete? I mean you only have three choices – on the top, on the bottom, or on the edge. OK, you might have some combination of the three as well.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

A website discussing the use of consumer-grade small electric wind systems such as turbines to lower energy costs.

Report identifying the important aspects of building design and construction to enable installation of solar photovoltaic and heating systems at some time after the building is constructed.

A research paper exploring the design, installation, repair and maintenance of solar water and pool heating technologies.

Specifications to assist builders in designing and constructing homes equipped with a set of features that make the installation of solar energy systems after the completion of the home’s construction easier and less expensive.

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2016, and is available for...

A standard providing minimum energy efficiency requirements for buildings that are not low-rise residential buildings.

Website providing a link for purchasing NFPA 1141, Standard for Fire Protection Infrastructure for Land Development in Wildland, Rural, and Suburban Areas.

Website providing a link for purchasing NFPA 703, Standard for Fire Retardant—Treated Wood and Fire–Retardant Coatings for Building Materials.

Standard establishing requirements for the performance and installation of gasketing systems including mortised to doors, frames or both which was published in the year 2021 and a can be purchased to be viewed in full from the ANSI webstore in the link.

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

Website providing a link for purchasing NFPA 1144, Standard for Reducing Structure Ignition Hazards from Wildland Fire.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Webpage containing the latest version of ANSI/RESNET/ICC 380, Standard for testing Airtightness of Building Enclosures, Airtightness of Heating and Cooling Air Distribution Systems, and Airflow of Mechanical Ventilation Systems. This standard provides a consistent, uniform methodology for evaluating...

Link to find the latest version of ANSI/RESNET/ICC 301, a standard providing a methodology for calculating Energy Rating Index for code compliance.

Website containing links to key wildfire codes and standards.

Standard covering the installation of fenestration products in new and existing construction, which was published in the year 2019, and is available for preview and purchase at the referenced link.

Standard covering the installation of fenestration products in new and existing construction which was published in the year 2007, and is available for preview and purchase at the referenced link.

Detailed requirements for testing, exposure modeling, and allowable limits for modeled indoor air concentrations.

Standard specification covering the minimum performance and acceptance criteria for an air barrier (AB) material or system for framed walls of low-rise buildings with the service life of the building wall in mind.

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2022, and is available for preview and purchase at the reference link. There are also other versions of...

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2023, and is available for preview and purchase at the reference link. There are also other versions of...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2011 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2021, 2015, 2006, and...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2021 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2015, 2011, 2006, and...

Standard specification covering the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements...

ASTM standard for wood-composite decking and guardrail materials under a variety of tests, including fire performance and UV resistance. Available for preview and purchase at the reference link.

A specification covering the application of Insulating Concrete Forms (ICFs) that act as permanent formwork for cast-in-place reinforced concrete beams & walls which was published in the year 2022 and is available for preview and purchase at the reference link.

Test method designed to calculate an assigned air permeance of flexible sheet or rigid panel-type materials at a reference air pressure differential of 75 Pa which was published in the year 2021 and is available for preview and purchase at the reference link.

Standard describing a test method measuring air-leakage rates through a building envelope under controlled pressurization and de-pressurization which was published in the year 2019 and is available for preview and purchase at the reference link.

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

Standard describing a test method for mold growth resistance on interior coatings such as paint in an environmental chamber; the 2021 version of this standard is available for preview and purchase at the referenced link.

Test method providing a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. This version of the standard was published in the year 2021 and is...

Test method designed to obtain reliable values for the WVTR of plastic film and sheeting which was published in the year 2020 and is available for preview and purchase at the reference link.

Standard describing two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone which was published in the year 2022 and is available for preview and purchase at the reference link.

The Standard Work Specifications (SWS) are a tool for industry guidance to ensure effective, durable, and safe work is performed during home upgrades.

Report recommending strategies and approaches that the Federal government and other stakeholders may take to encourage and aid States and local communities in the adoption of the most current building codes.

Research study providing a comparison of selected retrofit activity typically done, versus that same retrofit activity approached from an integrated high performance remodeling and quality management perspective.

The 2017 publication update to the SEAOC Wind Committee and SEAOC Solar Photovoltaic Systems Sub-Committee's 2012 report.

Fact sheet describing recommendations for exceeding NFIP regulatory requirements for new construction and for repairs, remodeling, and additions, including building foundations, enclosures below the Base Flood Elevation (BFE), use of nonstructural fill, use of space below the BFE, utilities...

Research study determining how well high performance envelope and innovative cooling system interact to cost effectively reduce cooling energy use in this hot-dry climate.

A guide for homeowners on determining the risks from tornadoes and hurricanes and selecting a safe room type and location, as well as providing detailed plans for safe room construction.