Library

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

Standard providing a methodology for calculating Energy Rating Index for code compliance.

2015 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2015 edition of code establishing regulations involving life and property safety from fires and explosion hazards, including emergency planning, fire department access and water supply, automatic sprinkler systems, fire alarms, and hazardous materials planning and storage.

2015 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

A colored map showing seismic zones across the United States, ranging from lowest to highest seismic hazards.

Report assessing and scoring code enforcement and administration and contractor licensing in the 18 states most vulnerable to catastrophic hurricanes along the Atlantic Coast and the Gulf of Mexico.

Code set from IAPMO explaining plumbing standards. 2018 publication.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Report telling consumers the risks of radon, how radon gets into a home, and steps consumers can take to reduce radon exposure in their homes.

Guide for homeowners describing how to find and seal basement and attic air leaks, determine if attic insulation is adequate, make improvements safely, and reduce energy bills.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Vinyl siding estimating and installation guide for vinyl siding products.

Standard outlining industry procedure for sizing residential duct systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Standard providing a universally accepted definition for quality installation for residential and commercial heating, ventilating, and air conditioning applications.

Document detailing the requirements, roles, and obligations for participants in an organized effort, ensuring that HVAC installations comply with the ANSI/ACCA 5 QI – 2010 (HVAC Quality Installation Specification) QI Standard.

Acceptance criteria providing guidelines for demonstrating compliance with codes referenced in the criteria related to barriers to water migration in thin-set installations of ceramic tile and stone flooring and shower sub-pan linings.

Article describing how to detail head flashing above a window.

Report on the design and evaluation of extended plate and beam.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Article describing how an airtight home shell helps achieve a tight envelope that is energy efficient and cost effective.

Updated detailed information about Formaldehyde.

Report describing a field investigation of failure rates of whole-house mechanical ventilation systems installed in Florida homes.

Article describing air sealing and air barriers in buildings.

Standard establishing the minimum whole-building energy performance requirements for energy efficient residential buildings.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

A basic guide walking through the various types of valves useful in mitigating the effects of earthquakes and other seismic events on natural gas pipelines for residential use.

Fact sheet describing recommended practices for installing brick veneer that will enhance wind resistance in high wind regions and examples of proper installations and brick veneer tie spacings; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Document providing background and approach for the prep work necessary prior to adding attic insulation - focusing on combustion safety, ventilation for indoor air quality, and attic ventilation for durability.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Report covering interior energy retrofits of masonry buildings.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

Article describing different kinds of water-resistant backer boards.

Information sheet from FEMA on preparation for extreme heat, including measures for keeping homes cool.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Document providing guidance to U.S. home builders who want to accept the challenge.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

Report summarizing the guidelines for developing and reporting analytical results in a consistent and meaningful manner for all home energy uses.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Research study describing a number of promising foundation and basement insulation strategies that can meet the requirement for better thermal control in colder climates while enhancing moisture control, health, and comfort.

Report comparing a variety of roof insulating strategies to present their advantages and disadvantages according to several comparison criteria.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

An article discussing how different metal roof materials and attachment methods affect the ability of the roof to thermally expand and contract and the durability of different solutions.