Library

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2009 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Florida building code including all the amendments and additions by Florida for the wind-borne debris regions and the high-velocity hurricane zone.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Article from the Sierra Club explaining 5 steps to take to ensure your home's resistance to wildfires, including site maintenance and roof construction guidelines.

Article describing seven reasons to mulch gardens.

Paper describing a proposed method for quantifying tree and vegetation evapotranspiration effects on city climate

Report describing an air distribution system composed of a series of uniformly-sized ducts that terminate in rooms throughout the home and return to a central manifold, similar in fashion to a “home-run” cross-linked polyethylene plumbing system.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Report describing the experience gained from AIA’s Disaster Assistance Program with first-hand accounts of disaster response and recovery, case studies and other best practices, including approaches to designing buildings to be more adaptable to uncertainty.

Webpage providing mapping tool for obtaining ground snow load, based on ASCE 7-10, for any location in the contiguous United States, with the exception of locations requiring a case study due to extreme local variations in ground snow loads. Fee required for some data.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Fact sheet describing recommended practices for installing brick veneer that will enhance wind resistance in high wind regions and examples of proper installations and brick veneer tie spacings; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Document providing background and approach for the prep work necessary prior to adding attic insulation - focusing on combustion safety, ventilation for indoor air quality, and attic ventilation for durability.

Article describing different kinds of water-resistant backer boards.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Webinar answering code-related questions on duct leakage tests, moisture levels in attics and crawlspaces, combustion equipment in conditioned attics, ventilation in multifamily buildings, and continuous insulation in residential construction.

Report providing water management details for roof assemblies.

Document providing guidance to U.S. home builders who want to accept the challenge.

Report summarizing the guidelines for developing and reporting analytical results in a consistent and meaningful manner for all home energy uses.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Research study describing a number of promising foundation and basement insulation strategies that can meet the requirement for better thermal control in colder climates while enhancing moisture control, health, and comfort.

Report comparing a variety of roof insulating strategies to present their advantages and disadvantages according to several comparison criteria.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Article published by American Society of Civil Engineers on different building types and their effectiveness resisting extreme heat from a building envelope perspective.

Report describing ventilation system design, including a central fan integrated supply (CFIS) system, made up of a 6-inch outdoor air intake duct connected to the return side of the air handler with a fan cycling control to make sure the fan runs a programmed minimum amount of time.

Website providing weather data.

Report assessing the science of climate change with a focus on the U.S.

ENERGY STAR clothes dryer buying guidance for consumers.

Fact sheet providing guidance and best practices on the selection of building materials used for coastal construction, and discussing flood, wind, corrosion, decay resistance, and protection recommendations; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact...

Fact sheet describing the characteristics that make for a successful coastal residential building, including design and construction recommendations; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Installation manual describing proper installation practices, industry standards and the code requirements of roofing tiles.

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height. Walls with...

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel sheathing (WSP) as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low...

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height.

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel (WSP) sheathing as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 in. thick over the WSP, and a cladding system installed over the foam sheathing in low...

Article describing the causes of wood decay and moisture issues.

Fact sheet summarizing NFIP requirements, general guidelines, and recommendations concerning the construction and installation of decks, access stairs and elevators, swimming pools, and accessory buildings under or near coastal residential buildings; also published in FEMA P-499 “Home Builder’s...

Fact sheet describing design and construction practices that reduce the likelihood of flood damage in the event that flood levels exceed the BFE, including illustrations of appropriate construction practices; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact...

Document providing design guidance and software tool information for forced-air HVAC systems.

Information about dense pack, cellulose insulation.

Information sheet with HVAC duct insulation, testing, maintenance and performance information.

Report providing an introduction to the NEHRP recommended seismic provisions for new buildings and other structures.

Presentation describing the history of ECM motors, an overview of ECM motor technology, and a lesson on the installation of ECM motors.

The objective of this research was to quantify the field performance of wood-frame walls clad with a variety of common claddings in a mixed-humid climate.