Library

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Code set from IAPMO explaining plumbing standards. 2012 Publication.

2015 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Code set from IAPMO explaining plumbing standards. 2015 publication.

2018 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Federal statistics about national energy consumption in residential homes in 2020

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Article describing thermal bridging, construction practices that encourage thermal bridging, and solutions.

Report describing the results of a field study of five different ventilation system types in 29 homes in the Pacific Northwest.

Report describing an air distribution system composed of a series of uniformly-sized ducts that terminate in rooms throughout the home and return to a central manifold, similar in fashion to a “home-run” cross-linked polyethylene plumbing system.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Information sheet about unvented fireplaces and combustion safety.

Report examining the structural properties and applications of an innovative studless building system, detailing its testing regime and providing an engineering guide for architects and engineers.

Report on the design and evaluation of extended plate and beam.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Report describing approaches to using less wood in home building that minimize waste.

Fact sheet describing advanced framing techniques that reduce the amount of lumber used in constructing wood-framed houses while providing more space for wall insulation.

Fact sheet describing advanced wall framing.

Report (1) compares existing measurement methods, based on field testing in a wide range of buildings, (2) presents the development of two new methods to directly measure exterior and interior leakage of an attached unit, and compares to existing methods; and (3) experimentally evaluates the...

Technical report describing the SPS (Structural Panel System), an innovative implementation of the "perfect wall" concept, situating environmental control layers on the exterior side of structural components for improved constructability, cost-effectiveness, and performance, validated through the...

Website providing research, efficiency and safety standards development, and advocacy to the home appliance industry to bring efficient, high-performing home appliances to consumers.

Website reporting efficiencies for dehumidifiers, room air conditioners, and room air cleaners that are tested by independent laboratories and reported by the Association of Home Appliance Manufacturers.

Report describing two retrofit duct sealing techniques - manually-applied sealants and injecting a spray sealant, that were implemented in several low-rise multi-unit buildings in North Carolina.

Website article interviewing the inventor of the Larsen truss, a history of its use, and a discussion of its advantages and disadvantages.

Report providing information regarding the benefits and challenges associated with the installation of earthquake-actuated automatic shut-off valves (ASVs) or remote-control valves (RCVs) to stop the flow of natural gas into buildings in the event of an earthquake or rupture of the gas line.

Report with updated energy consumption data for 28 residential & commercial miscellaneous electric loads (MELs), including projections to 2040.

Report on adding insulation to load-bearing mass masonry buildings.

Safety brochure from the Consumer Product Safety Commission (CPSC) describing the dangers to children of furniture tipping over if it is not securely anchored.

Website providing consumers with information about the risk to children from appliances and furniture tipping over and ways to anchor furniture and appliances to prevent this hazard.

ASHRAE Standard prescribing an field evaluation and test method to measure and score the performance of unitary HVAC systems.

This ANSI/RESNET/ICC standard provides a consistent, uniform methodology for evaluating the airtightness of building, dwelling unit, and sleeping unit enclosures and heating and cooling air distribution systems, and the air flows of mechanical ventilation systems.

Standard covering updates to the expected leakage rates for ductwork constructed to the SMACNA HVAC Duct Construction Standards—Metal & Flexible, duct leakage test procedures; includes recommendations on use of leakage testing, types of test apparatus, and test setup and sample leakage analysis.

Webpage describing different types of appliance thermometers, how they work, and how they should be used by homeowners.

The exhaust from residential combustion appliances contains air pollutants and high levels of moisture that must be conveyed to the outdoors to maintain acceptable indoor quality.

A basic guide walking through the various types of valves useful in mitigating the effects of earthquakes and other seismic events on natural gas pipelines for residential use.

Standard establishing test methods for determining air leakage in duct systems using fan pressurization in low-rise residential and commercial buildings.

Brochure explaining the essential basis for advanced framing and some of the more common advanced framing details.

Document providing guidance to U.S. home builders who want to accept the challenge.

A book about structurally insulated panels.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Report considers a number of promising wall systems that can meet the requirement for better thermal control.

Document about testing software predictions of retrofit energy savings in existing homes.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Presentation about advanced framing techniques.

California Office of the State Fire Marshal's homepage for the Building Materials Listing Program, providing builders, contractors, architects, and others with access to a database of fire alarm systems and fire-resistant construction materials including roof coverings, wall, ceiling, and floor...

California Office of the State Fire Marshal's compiled and searchable list of different building materials and their test results for fire resistance.

Document presenting some of the key technical properties of many of the most common building materials.

Website providing CAD files and drawings of advanced framing details.

Website providing information about building plans for the ENERGY STAR thermal bypass checklist.