Library

Report detailing field walk-through evaluations, energy simulations for projected savings with exterior insulation upgrades, building envelope energy improvement cost estimates, and installation and maintenance of monitoring equipment and data.

Research report presenting results of short term tests on measures used in an energy efficiency retrofit project in California.

A article about the best practice method of installing fiber cement siding, to install flashing at the butt joints of the siding boards, rather than face caulking the butt joints afterwards.

Report describing a laboratory assessment that provides insights into space requirements and venting strategies for heat pump water heaters (HPWH) to enhance retrofit installations and provide actionable guidance for manufacturers, designers, engineers, installers, and owners.

Report discussing the potential energy savings of new high-efficiency downlights, and the results of product testing to date.

Report sumarizing results of an ICF investigation of side-by-side houses in Knoxville, Tennessee.

Website blog with guidance about calculating heat-loss.

Correcting pressure imbalances in your HVAC system can result in a healthier, more efficient home.

Article describing the second step of a three-step process for the installation a tubular skylight, using peel-and-stick flashing tape instead of roof cement, and integrating the roof underlayment with the flashing.

Article describing how to counterflash a chimney by tucking the upper pieces of counterflashing into the chimney mortar joints and overlapping them over the various pieces of base flashing, which are nailed to the roof deck.

Report with guidance for installing windows with foam sheathing on wood-frame walls.

Report describing the results of a 21-home field study investigating the effectiveness and failure rates of whole-house mechanical ventilation systems installed in Florida homes over the last 15 years.

Article showing steps for kick out flashing at roof-wall intersection.

Report describing research conducted to support California’s Title 24, Part 6 Building Energy Efficiency Standards by analyzing the impact of installation location and ventilation on heat pump water heater (HPWH) performance, emphasizing the need for proper installation to maximize efficiency...

Article describing a technique for installing a skylight and avoiding potential water leaks with the use of a peel-and-stick (or self-adhesive) membrane under the flashing.

Report using a field test plan to evaluate the success of implementing energy efficiency upgrades at the community scale incorporating whole-house systems integrated measures package (SIMP).

Factsheet describing how to test the duct leakage of a manufactured home in the manufactured home factory.

Article describing the flashing of roofs and what to look for, targeted at home inspectors.

Siding installation guide for Ply Gem Siding Group products.

Measure Guideline describing how to assess and carry out the isolation of natural draft combustion appliances from the conditioned spaces of low-rise residential buildings.

This measure guideline provides guidance on combustion safety inspection procedures for appliances and heating equipment that use indoor air for combustion and dilution of flue gases in low-rise residential buildings.

Measure Guideline research report providing simple, long term, and durable solutions when using tapes and flashing membranes in conjunction with the exterior face of rigid polymeric foam sheathing to create the drainage plane of a wall system.

Repor ourlining testing results from a 53 home monitored sample, long-term energy use of electric resistance clothes dryers.

Report describing a lighting and smart power strip retrofit evaluation that was conducted on 56 all-electric, existing Florida homes to see how lighting and miscellaneous electric loads might be reduced.

Report describing an analysis method for determining optimal residential energy efficiency retrofit packages and applies the analysis method to a 1960s-era home in eight U.S. cities.

Standard that prescribes a testing method to determine the efficiency of space heating and/or cooling thermal distribution systems under seasonal and design conditions. This version of the standard was published in the year 2014, and is available for preview and purchase at the reference link. The...

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

Document about development of a new test procedure to increase the quality and accuracy of energy analysis tools for the building retrofit market.

Report covering wind loading on roofing assemblies.

Report presenting performance results from tests conducted on an energy efficiency retrofit project in Stockton, California.

Paper examining the monitored performance of four newly constructed near zero energy homes in Florida.

Report briefly reviewing past research on the effects of occupant behavior on residential energy use and then covering a two year pilot evaluation of a low cost residential energy feedback system installed in twenty case study homes in Florida.

Report briefly reviewing past research on the effects of occupant behavior on residential energy use and then covering a two year pilot evaluation of a low cost residential energy feedback system installed in twenty case study homes in Florida.

Report designed to help a builder understand quality management and its role in transitioning from conventional to HPH building and remodeling.

Paper covering a parametric study of foundation heat exchanger-based ground source heat pump systems for several house configurations in a range of European locations, with an emphasis on determining feasible combinations.

Report summarizing the results of laboratory testing of 20 advanced power strip products.

Fact sheet describing flashing of roof penetrations to make a home more resistant to high winds, hurricanes, and rainwater intrusion.

Report about a tool developed to enable users to compare a typical 1970s ranch home against an IECC 2009 code-compliant home of the same configuration and against the 70s base case plus retrofits.

Research report detailing Florida Solar Energy Center (FSEC) partnership with Manatee County Habitat for Humanity to design a compact, Zero Energy Ready Home in Florida, tackling challenges like equipment sizing and indoor air quality, offering insights for projects surpassing building code...

Report summarizing commissioning, short-term testing, and analysis that occurred before, during, and just after the actual retrofit of the Bay Ridge project.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

Research study presenting a unique opportunity to both identify and evaluate deep retrofit measures that are practical and potentially cost effective for the retrofit market, as well as review the cost effectiveness of the Passive House design approach for achieving energy savings in deep retrofits.

Standard describing methods for testing the airtightness of buildings and HVAC equipment.

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

Test method designed to calculate an assigned air permeance of flexible sheet or rigid panel-type materials at a reference air pressure differential of 75 Pa which was published in the year 2021 and is available for preview and purchase at the reference link.

Test method providing a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. This version of the standard was published in the year 2021 and is...

ASTM standard test method for surface burning response of different building materials which was published in the year 2022 and is available for preview and purchase at the reference link.

ASTM standard test method for testing the surface burning response of different building materials which was published in the year 2023 and is available for preview and purchase at the reference link.

Standard that describes the principles for the design of a hot box apparatus and the minimum requirements for the determination of steady state thermal performance of building assemblies when exposed to controlled laboratory conditions. The current version of the standard was published in 2019, and...

Test method designed to obtain reliable values for the WVTR of plastic film and sheeting which was published in the year 2020 and is available for preview and purchase at the reference link.