Library

Web article describing common issues that can cause refrigerant system flare joints to leak.

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2012 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2015 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2018 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2019 version of the California Residential Code.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Article from the Sierra Club explaining 5 steps to take to ensure your home's resistance to wildfires, including site maintenance and roof construction guidelines.

Paper describing a proposed method for quantifying tree and vegetation evapotranspiration effects on city climate

Vinyl siding estimating and installation guide for vinyl siding products.

Guide describing advanced framing, a system of construction framing techniques designed to optimize material usage and increase energy efficiency.

Report describing approaches to using less wood in home building that minimize waste.

Website providing research, efficiency and safety standards development, and advocacy to the home appliance industry to bring efficient, high-performing home appliances to consumers.

Case study about high humidity, mold and condensation on surfaces in S. Florida, and how building characteristics cause and amplify these problems.

Fact sheet describing air-sealing concerns and remedies, including HRV/ERV installation, caulking, spray foam, and weatherstrip installation.

Standard detailing the specific requirements for all face, back, and inner ply grades as well as formaldehyde emissions, moisture content, tolerances, sanding, and grade marking which was published in 2020, can be acquired through a subscription with the ANSI webstore.

Updated detailed information about Formaldehyde.

This ANSI/RESNET/ICC standard provides a consistent, uniform methodology for evaluating the airtightness of building, dwelling unit, and sleeping unit enclosures and heating and cooling air distribution systems, and the air flows of mechanical ventilation systems.

Standard covering updates to the expected leakage rates for ductwork constructed to the SMACNA HVAC Duct Construction Standards—Metal & Flexible, duct leakage test procedures; includes recommendations on use of leakage testing, types of test apparatus, and test setup and sample leakage analysis.

Website homepage of APA – The Engineered Wood Association, a nonprofit trade association combining the research efforts of scientists and engineers, APA promotes new solutions and improved processes that benefit the entire industry.

Report covering moisture and leakage issues associated with spray foam insulation application to the underside of roof sheathing.

Power Point PDF presentation on historical architecture in New Mexico

A report that evaluates the force it takes to crack stucco of various thicknesses.

Technical report describing the evaluation of air management systems in a high-rise apartment building in Toronto, Ontario, focusing on air leakage, suite depressurization, and the performance of in-suite exhaust and corridor ventilation systems.

Standard establishing test methods for determining air leakage in duct systems using fan pressurization in low-rise residential and commercial buildings.

Article describing how demand plumbing systems send cold water back to the water heater until hot water arrives at the sink, shower or other fixture where it is needed.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Case study describing solar thermal and photovoltaic systems in new construction.

The Builder's Guide provides the building industry with the latest and best practical information on how to apply building science principles to structures as systems in hot-humid climate regions.

Case study describing solar thermal and photovoltaic systems in new construction.

Case study describing solar thermal and photovoltaic systems in new construction.

Website with consumer and contractor information about building codes and regulations for solar water heating systems.

California Office of the State Fire Marshal's homepage for the Building Materials Listing Program, providing builders, contractors, architects, and others with access to a database of fire alarm systems and fire-resistant construction materials including roof coverings, wall, ceiling, and floor...

California Office of the State Fire Marshal's compiled and searchable list of different building materials and their test results for fire resistance.

Document presenting some of the key technical properties of many of the most common building materials.

Document detailing how to build radon-resistant homes.

Article describing the principle of capillarity in construction materials.

Source for information about Carbon Monoxide including health effects and measures to reduce exposure.

Book describing Carpentry and Construction, Construction Materials, Hand Tools, Power Tools, Construction Equipment, Jobsite Safety, and Working Conditions, Building Design and Print reading, Inspections Survey Instruments and Operations, Foundation and Outdoor Slab Construction, Floor, Wall, and...

Document with information from a workshop addressing framing materials for residential buildings in California. A copy of the document can be requested at the resource link, and an online copy of the document can be found by searching for it on the California Energy Commission's Library Online...

Document providing guidance about choosing the correct caulk for a project.

Report on the stability of furring strips as a means for cladding attachment over walls with thick exterior rigid insulation.

Fact sheet that details the steps needed to perform a combustion appliance safety inspection to determine if fossil fuel-fired appliances are operating safely under a depressurized condition.

Information sheet discussing the properties and benefits of insulating concrete forms.

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel sheathing (WSP) as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low...

Article describing the use of whole-house fans to provide cooling in the region surrounding Sacramento, CA.

Report describing the monitored long-term performance of two solar domestic water heating systems in northern climates.

Technical bulletin addressing surfacing options in regards to composite wood panels and their emission barrier capabilities.